Aspen Standard Peristaltic Condensate Pump Fp2081

The Aspen Standard peristaltic pump is triggered by the hard-wired cooling signal from the air conditioning unit. The Standard is designed to fit in ceiling voids and lift the condensate water from wall mounted machines where a gravity drain is too obtrusive.

It can also be used on cassettes fitted with an internal lift pump. The pump can be mounted remotely as it is self-priming to a height of 3 metres and will pump 6.25 litres of water per hour against a maximum head of 12 metres.

The pump runs constantly while the air conditioning system is cooling Èöwhen the cooling switches off a 3 minute timer ensures that the condensate tray is emptied before the pump switches off. Rollers in the pump act as check valves to stop the condensate draining back into the condensate tray. The Standard pump is a peristaltic rotary type - which means that it is quiet in operation, very reliable and will run dry without fear of damage or embarrassing noise. The Standard does not suffer from corrosion or contamination problems.

Technical Specifications

Operates on hard-wired 150-230V cooling signal

Self-priming lifts 3 metres

12 metres discharge head

Water flow rate: 6.25 ltrs per hr @ 12 metres head

3 minute timer overrun

No siphoning back

No loud sound from dry running

Manual test switch

Pumps water, fibrously contaminated water and air

Pump rating: 0.2A, 230V AC
Alternative voltages available

Fire retardant plastics

Inlet/outlet size: 6mm

Push-in plug

Wall-mounted bracket

Dimensions:
115mm(H) x 135mm(W) x 77mm(D)

Standard Peristaltic Pump By Aspen Pumps

Simply connect the Standard peristaltic pump
to the appropriate drip tray (using the vinyl tube supplied), mains supply and control link to the
air-conditioning units cooling signal. The pump
can be mounted remotely as it is self-priming to
a height of 3 metres (9.8ft) and will pump 6.25 litres (1.65 US gallons) of water per hour against a head
of 12 metres (40ft).

The Standard pump is designed to run constantly
while the air conditioning system is cooling.

This is achieved by linking the pump to the cooling signal. When the cooling switches off, a timer in the pump ensures that the drain tray is emptied before the pump switches off. The signal wire can be connected to the cooling signal and therefore on heating, the pump does not run.

The pump is a peristaltic rotary type - which means that it is quiet in operation, very reliable and will run dry without fear of damage or any embarrassing noise. It is not sensitive to water borne contaminants as reciprocating pumps are, and there is no mechanical water sensor to fail!

It is designed to fit in ceiling voids and lift the condensate water from wall mounted machines where a gravity drain is too obtrusive. It can be used on cassettes fitted with an internal lift pump. The rollers act as check valves to stop condensate draining back into the drip tray.

The standard pump now has a new push in plug which makes installation and maintenance easier.

Aspen Standard Service Guide

Inspect pump head regularly and change the pump head tube every 12 months or more frequently if required.

If any problems with the pump occur check the
tube first!

To remove pump head make sure the roller assembly is vertical. Remove transparent cover and fit replacement pipe. The addition of a smear of silicon grease will ease the refitting of the lid, reducing potential friction noise.
This only takes 3 minutes!

The test switch should always be returned to the NORMAL position after inspection.

ELECTRICAL CONNECTIONS:
Brown - Permanent/Live
Blue - Neutral
Green/Yellow - Earth
Black - Switched live from signal (110-240V)

Aspen Standard Technical Specifications

Operates on 240V cooling signal 
Self-priming lifts 3 metres (9.8ft)  
12 metres discharge head 
Water flow rate: 6.25 ltrs (1.65 US gallons)
per hr @ 12 metres (40ft) head 
3 minute timer overrun 
No siphoning back 
No loud sound from dry running
Fits into shallow ceiling void 
Pumps water, fibrously contaminated
water and air
Pump has a manual test switch   
Pump rating: 0.5A, 240V AC
Alternative voltages available

Maximum water temperature: 40C
Fire retardant plastics

Aspen Standard Installation Notes

This pump is designed to be sited upright in any position, but at all times it must have free space around the case for ventilation. Ensure that there
are no kinks or trapped sections in the piping.
Vinyl piping must have an ID 1/4 by OD 3/8.
Fix the pipes with the tie wraps to the pump outlet
and inlet.

A variable connector is provided to make easy installation between the condensate tray outlet and vinyl tube.